Lab Report Essay

Submitted By ylaimoun

Words: 637

Pages: 3

Open Document

Purpose of the experiment

In this experiment, we are assuming an unknown vaporized liquid has ideal gas properties. Based on this we will use the Ideal gas law and stoichiometry to calculate the Molar mass. Based on numeric and qualitative data we might make an assumption as to the identity of the liquid.

Materials

A special round bottomed flask

Aluminum foil

Pipette to transfer unknown liquid

accurate digital scale

A hot water bath setup.

Graduated cylinder

Ice bath setup

Experimental procedure:

We obtain the mass of the empty flask, aluminum foil (both pieces) and rubber band.

To find the volume of the flask, we fill it with water and then transfer that to a graduated cylinder for measurement. Since we are not using a rubber stopper this will provide us with an accurate measurement.

Transfer a small volume of the unknown liquid to the flask.

We immerse the flask in the hot water bath and secure with a clamp to the stand.

We aim to reach a steady boil temperature. The aim is to volatilize the unknown liquid and drive out any air in the flask. At this point we assume the temperature and pressure of the gas has equalized with the surrounding bath and atmosphere (respectively).

We are instructed to allow this to continue for 5 minutes. we then, cover the flask with the second piece of aluminum to trap any gas inside the flask and then plunge the flask in the ice water bath after tempering slightly with cold water.

We can then measure the mass of the condensed liquid.

Measurements and Calculations

Pressure mmHg
767.6

Pressure atm
1.01

R (cm3 atm K-1 mol-1)
82.055

T (C)
98.6

T (Kelvin)
371.75

Volume of flask (ml)
981

mass of flask (g)
78.64

mass of Al foil (1) (g)
0.241

mass of Al foil (2) (g)
0.171

rubber band (g)
0.248

mass of flask+liquid (g)
80.73

mass of liquid(g)
1.434

Mr=mass/moles
Mr = m*R*T PV

Mr = 1.43*82.06*371.75 981*1.01
= 44.14

Conclusion and Error Assessment

Based on molecular mass estimate obtained and other qualitative data; Odor and familiar high solvent effect on nail polish, we guess that the identity of the unknown liquid is Acetone which has a Mr of 58.08

Error

Lab Report Format

ANATOMY & PHYSIOLOGY CLASS: WRITING LAB REPORTS The following is an explanation of the format that is to be used for writing lab reports. There will be lab activities for each Chapter in the textbook. 1. Lab Report grades are given the same value as a test grade. It is very important that they be done correctly and thoroughly. 2. All lab reports should be typed using Times New Roman and only 12 font. (no exceptions) 3. In the upper left hand corner include your name, high school, and A & P…

Words 1045 - Pages 5

lab report Essay

CHM1032L pre/post lab instructions Preparation is a key to success in this lab. For this reason, you are required to thoroughly read through the experiment information presented in the lab manual, and complete a pre-lab for each experiment you do. The prelab must be completed prior to the day of the experiment. Each Friday I will ask to see your completed prelab before I allow you to enter the lab. If you have not finished the pre-lab, I will not allow you to enter the lab and you will receive…

Words 1046 - Pages 5

Drosophila Lab Report

Drosophila Lab Report By Logan Aker University of Colorado, Boulder Principles of Genetics Lab, MCDB 2151, Tuesday 4 – 5:50pm TA: Alexander Martinez Abstract In this lab, we carried out two different crosses using Drosophila; a monohybrid cross and a sex-linked cross. This lab specifically tested Mendel’s laws of independent assortment and the law of segregation in genetics. We selected males and females of two different phenotypes and mated them (and their succeeding offspring)…

Words 1729 - Pages 7

Spectroscope Lab Report

Spectroscope Lab Report Naudia Blanton Period 9 Due: 1-2-14 Abstract: The purpose of the Spectroscope lab is simple. It is basically to see the spectrum of different light sources. Some of the light sources included are sunlight and a candle. It focuses on the difference between their spectrums. Background: Electromagnetic Spectrum - The range of wavelengths…

Words 445 - Pages 2

Lab Report Essay

Kinetics Lab Report Chemistry 152, Fall 2013 Kelli Forbes Susan Borowski Section: 5 September 2013 Abstract: For this experiment the main objectives were to determine the best wavelength to use for a Beer’s Law Analysis for the dye assigned which happened to be brilliant blue. The molar absorptivity of Brilliant Blue at 622.0 nm had an absorbency of 0.321. These results were obtained by completing a series of five cuvets…

Words 390 - Pages 2

Momentum Lab Report

Lab report #5 In this experiment, we used a nearly frictionless surface to compare velocity characteristics to that of momentum, suing different weights, as well as bouncing carts and sticking carts together. This is important to understand, because momentum is a combination of weight and velocity, where as velocity is independent of weight. The materials we used for this experiment include 2 carts, with weights of 139.7 grams and 290.4 grams. We also used springs on the ends to “bounce”…

Words 459 - Pages 2

Lab Report Essay

Sheffield International College AS1b SE FC Lab report Title:Lab report of the constant of elasticity Group:S204 Student ID:25436 Teacher:Simon Dale Elasticity experiment report Introduction: In physics, elasticity is the tendency of solid elastomeric material, while after deformation recovering to the original shape. And spring is one of the elastic objects which can return to the original size when forces were…

Words 901 - Pages 4

Lab Report Essay

MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18, 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes, M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine…

Words 1090 - Pages 5

lab report Essay

DO NOT COPY ANY MATERIAL FOR THIS REPORT. IF YOU COPY FROM THE LAB MANUAL OR ANOTHER SOURCE YOU WILL RECEIVE A ZERO FOR THE REPORT. WRITE EVERYTHING IN YOUR OWN WORDS. Experiment (Input Number): (Type full title here.) Name Date Class Title and Section Instructor: Katherine Walton Objective In this section you will discuss about the purpose of the experiment. It should only be a few sentences long and should include information pertaining to what it is you are trying to analyze…

Words 567 - Pages 3

Lab Report On Density

9/26/13 I have completed this lab report in accordance with the NA Honor Code. X_______________________________________________________ An Introduction to Calculating Density Introduction: Purpose: To determine the density of different substances using mass and volume measurements that have been calculated. Also, to familiarize oneself with the materials in the laboratory and to investigate the precision of measurements using precision of error. Hypothesis: If the density of a solid and…

Words 1492 - Pages 6