Nt1310 Unit 3 Data Analysis

Words: 523

Pages: 3

Open Document

Pseudo code 1: Pseudo code for CH selection
PSEUDOCODE:

1. Set flag to 1
2. Mobile Sensor Node for the INIT message
// cluster head election Initiates
3. IF flag is equal to1
4. wait for rquested node of data (Energy level and routing time) from all the sensors in the network
5. IF energy level is more than initial data size
6. select the node as CH from the base station
7. ELSE save the parameters
8. ENDIF
9. ELSE reform INIT message again
10. ENDIF

Cluster Formation The Mobile Sensor Node with higher signal strength responds to the initial message by sending their Node ID, its energy level, data routing timestamp and its signal strength. The cluster is formed based on distance coverage scheme which is the better coverage scheme and it covers a number of sensors efficiently.

Pseudo code 2: Pseudo code for cluster formation
1. Set flag to 1
2. CH chosen depends on cluster elected message to all …show more content…
After aggregating the data, the Cluster Head sends a notification message to the Mobile Sensor Node and goes to sleep mode based on energy level with repetition of data occurred. The Mobile Sensor Node sends wake up signal to the CH gathers. While communicating the
CH enters wake state and uploads the data to Mobile sensor Node. If two Cluster Head sends notification at the same time, the Mobile sensor Node can gather data from both CH simultaneously. The Mobile sensor Node data dynamically using genetic scheme. Firstly, the Mobile sensor Node data sends to the CH gathers and verifying the repeated message with having lower energy level and moves to another CH (inter cluster) communication. If the CH has any power issue and buffer overflow issue then it would send a warning message to Mobile sensor Node for gathering data immediately. The Mobile sensor Node gathers data immediately and returns to the Base station for uploading the data to change the

Nt1310 Unit 3 Data Analysis

process who do not have the appropriate credentials. 2. Metadata Analysis: By simply looking at who calls whom and how many times one can establish a relationship between the sender and the receiver. The number and the lengths of the messages are enough to establish the intent. For example if I say that that two parties exchanged 30 messages then we could conclude that there is a big enough conversation going on between them. 3. Impersonate: It is possible that a hacker can insert messages by impersonating…

Words 1471 - Pages 6

Nt1310 Unit 3 Data Analysis

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% \subsection {\label{eval-metric}Evaluation Metrics} \paragraph{} The set of measures and parameters we used for evaluating our SEES and comparing its performance with that of existing protocols are defined as follows: \begin{itemize} \item $F\!N\!D$ (First Node Dead): measures the length of the stable region which is defined as the number of rounds from the beginning of network operation until the first node dies. \item $L\!N\!D$ (Last Node…

Words 430 - Pages 2

Nt1310 Unit 3 Data Analysis

The random data is encoded using the convolutional encoder and produce an output with 128 bits that contains not only this data but also additional redundant information that can be used to protect the data of interest in the event of errors during transmission. The 1/2 code rate is used in this encoder. For every 1 input bit, the convolution encoder outputs is 2 bits. The encoded data is as shown in Figure 6. Fig. 6. Encoded bits V. TRANSMITTED DATA The encoded bits is given to the interleaver for…

Words 508 - Pages 3

Nt1310 Unit 3 Assignment 3 Data Analysis

Step 1. The smart node that received an advertisement message generates M0 and H0 for self-verification and sends them to the gateway. Step 2. The gateway that received M0 and H0 generates M1 and H1 and sends them to the CA manufacturer. Step 3. The CA that received information from the gateway obtains two random numbers through decoding and verifies H0 and H1 through searched PW. It generates M2 and M3 and sends them to the gateway. Figure 5. Initial authentication and device registration process…

Words 907 - Pages 4

Nt1310 Unit 3 Assignment 3 Data Analysis

company’s data is very important. Making sure it stays secure is the most important part of backing it up. Whether you are choosing open source software or commercial, you need to make sure it is the best option for your company. Which type of server is going to be used, dedicated or service provider? Where are the backups going to be stored, hard disks, tape media, or somewhere else? Who exactly is responsible for verifying the backups and restoring the data? Why does the data on the back…

Words 543 - Pages 3

Nt1310 Unit 3 Data Analysis Paper

following fragment of code does: int x = 1; double y; y = x + 3; Answer 1: A type is something which categorizes data into subsections, with each subsection having a specific function in programming, for example, integers, doubles, and booleans are all types which have a particular and different purpose when used to store or process data in programming. Types help identify the amount of storage required to store a particular set of data. Therefore types each have a particular function when compiled…

Words 1148 - Pages 5

Nt1310 Unit 3 Data Forwarding Analysis

converted to the router's input path. And keep in mind that this will have to decide the proper path to transmit this packet to the next router, and this process is called forwarding. Figure 26.2 shows the router with the input path for the data. Data forwarding Routing Data routing depends on the forwarding process. Routing is done by a combination of different router redirection. This is a combination that decides how the package will pass. Therefore, routing must determine the route accepted by the package…

Words 712 - Pages 3