Essay Welding Lab

Submitted By Craig-Hunter
Words: 889
Pages: 4
Open Document
Welding of High Pressure vessels and pipelines Procedure Roadmap

This guide has been prepared to assist with the preparation of welding procedures required for a high pressure vessel. A overview of the following areas will be discussed giving a basic roadmap to creating a new weld procedure: Preparation
Provisional weld procedure
Preparation of material
Preparation of equipment
Heat treatment
Qualification test
Inspection
Documentation
Production

Preparation

Specification details of the material to be welded are gathered including the thickness of material, purpose of vessel and standard of weld to be achieved. The chemical composition and mechanical properties of the material, including yield and tensile strength should be tested and recorded. Results should be compared to the specification given by the manufacturer of the material. The most appropriate welding method, joint type and filler material should be determined taking account of the outcome required for quality, environment and reliability.

Provisional Welding Procedure
The provision procedure is set up to provide an opportunity to test the welding variables for a specific application. This assures repeatability is achievable by properly trained welders.

Preparation of Material
The edges or surfaces to be joined by welding shall be prepared prior to welding. Pipe rarely will be received in a condition suitable for welding. Generally, there will either be an oil or rust coating, or a coating to prevent corrosion. This could include paint, primer, varnish, epoxy or tar all of which are undesirable for welding. Cleanliness is critical to prevent defects leading to rejected welds and costly repair, so these coatings must always be removed. Both pipe ends must be cleaned, on the inside and the outside, at least 25mm beyond the edge of the bevel. All surfaces and edges shall be free from cracks or any other defects which would adversely affect the quality of the weld. All moisture, grease or other foreign material that would prevent proper welding or produce dangerous fumes, should be removed. All surfaces to be welded should be wire brushed prior to welding.

Preparation of equipment
Welding material should be stored in suitable conditions that will keep them dry and free from surface rust and other contaminants. All rods should be of the same chemical composition and match that stated by the provisional welding procedure. Any damaged rods which have been compromised should be discarded and not used. Welding equipment should be fit for its purpose complying with the appropriate
Standards. The equipment should be of a power commensurate with the provisional welding procedure requirements. All equipment should be maintained in a serviceable condition. Any measuring instruments used for testing and inspection should be calibrated in line with the manufacturers recommendations.

Heat Treatment
Good welding practice is essential in preventing the weld cracking, which includes preheating when needed. Any preheat specified is to be maintained during welding. If welding is interrupted and the temperature of the base metal falls below the minimum preheat temperature, then arrangements will be made to preheat again prior to restarting the weld.

Qualification tests
The most experienced and competent welder available should be selected to conduct the qualification test. The selected welder current certificates and qualifications should be checked to be valid and in date. Before beginning to weld the procedure should be checked to assure that the correct electrode is being used. This includes the diameter and the classification of the electrode. A qualified welding inspector should witnessing the qualification tests process to confirm compliance with the requirements of the relevant
Show More

Related Documents: Essay Welding Lab

KOSUN Solids Control Equipment Are on Sale in Domestic and Abroad Essay

separate holding tank where they await further treatment or disposal. Mud loggers usually go out and check the shakers for shaker samples that have circulated from bottom. They separate the shaker from the drilling fluid and take it into an onsite lab where they dry out the samples and label them according to depth. They then look at the samples and analyse what kind of rock they have at a certain depth. This helps determines what depth that type of rock was encountered. As usual, due to metal…

Words 515 - Pages 3

The Different Career and Technical Education Courses at Santa Fe College Essay

Services, Health IT, Organizational Management) • Construction and Technical Education (Air Conditioning, Apprenticeship, Automotive, Building Construction, Welding) • Education Programs (Early Childhood Education, Early Intervention, Educator Preparation) • Emerging Technologies (Biomedical Engineering, Biotechnology, Clinical Lab Science, Industrial Biotechnology) • Health Sciences (Nursing Programs, Dental Programs, Allied Health Programs) • Information Technology Education (Graphic…

Words 387 - Pages 2

Corrosion Fatigue Lab Report

Fall 2013 Material Engineering Lab ME251-0 Lab#8 Metal Tensile Testing Instructor Name: Ali Ghazinezami Student Name: Hassan AL-Tulaihi WSU ID:V222W652 Due date: 11/06/2013 Class time: 1:30 to 4:30 INTRODUCTION: Corrosion fatigue of structural metals and alloys considers as process that is influenced by the number of factors, including stress level and strain-stress state, material microstructure and environment Developments in fracture mechanics approaches have provided the…

Words 934 - Pages 4

Essay on Slide 09 Fabrication

Introduction to Micro- and Nano-fabrications ECE440 Nanoelectronics Zheng Yang (e-mail: yangzhen@uic.edu; ERF3017) Department of Electrical & Computer Engineering University of Illinois at Chicago The first transistor: Bell Labs, December 23, 1947 Excellent reference: Hans Queisser, The Conquest of the Microchip, Harvard University Press, 1988 Page 2 Integrated Circuit Manufacture 0.75 micron dielectric features Integrated circuit 1992-1998 0.18 micron dielectric features Integrated circuit…

Words 2169 - Pages 9

Metallurgical Analysis On Three Parts From A North American Automotive Engine

INDUSTRIAL METALLURGY: IDENTIFICATION EXHAUST MANIFOLD 1.0 Introduction The purpose of this report is to perform a complete metallurgical analysis on three parts from a North American automotive engine. The three parts had to include a head bolt, ferrous part, and non-ferrous part. The parts chosen were a head bolt, piston, and exhaust manifold. The objective of the analysis was to determine from what material the parts were made and how the metal parts were processed to bring it to its final…

Words 2748 - Pages 11

Information Systems of Sterling Urgent Care Essay

IT190-1501A-01 : Introduction to IT Information Systems of Sterling Urgent Care Ryder May 02/09/15 TOC Section 1: Information Systems Overview 4 What is Sterling Urgent Care? 4 Choosing the Right Information System for SUC 4 Section 2: Information Systems Concepts 7 Types of Communication 7 SUC’s Communication Technology 8 SUC’s Virtual Private Network 9 Section 3: Business Information Systems 11 Data Systems 11 TPS (Transaction processing system) 11 MIS (Management information…

Words 5661 - Pages 23

CE360 Chapter 2 Materials For Concrete Essay

Chapter 2: Concrete-Producing Materials CE360 Reinforced Concrete Design Dr. Chun K. Seong School of Engineering Saint Martin’s University The course material is prepared, based on the textbook “Design of Concrete Structures” written by Arthur H. Nilson, David Darwin, Charles W. Dolan, published by McGraw Hill Objectives • To learn about components of concrete members: Cement, Aggregates, Admixtures, Water • To learn about Proportioning and Mixing Concrete • To learn about concrete conveying,…

Words 4499 - Pages 18

Speedo Innovation Essay

Speedo innovation: Swimwear companies have invested millions designing high-performance suits for the upcoming Beijing Olympics. Can design help swimmers finish faster? Following the 2004 Athens Olympics, officials at swimwear giant Speedo had good reason to celebrate: Athletes clad in their latest suits at the time, called Fastskin FSII, won 46 medals in the pool. Yet when the company's in-house design team, Aqualab, gathered soon after the games at company headquarters in Nottingham, Britain…

Words 5165 - Pages 21

Investing For Our Future Essay

Investing For Our Future Our world is changing faster than ever before in human history. We are experiencing the dawn of a revolutionary transformation. All around us we can see it happening. We live in an age of endless knowledge at the touch of a button. Just imagine, the entire world of wisdom small enough to hold in your hand. We live in an age with machines that can explore the deepest ocean trenches and rockets that can free themselves from earths gravitational pull. We live in an age where…

Words 6415 - Pages 26

A Study of Financial Performance of RSSKN Using Ratio Analysis Essay

CONTENTS | | | | |Sl. No. |Titles |PAGE.NO. | |I |Chapter 1 | | | |Executive summary |7 | | |Methodology…

Words 9860 - Pages 40