Which Of The Following Describes The Collision Domain Design Trade-Offs?

Submitted By michaellong41
Words: 1984
Pages: 8

Provides the capability to restrict the number of MAC addresses allowed to communicate through
24.)This option correctly describes the port security feature found on Cisco switches.
a. Provides the capability to restrict the number of MAC addresses allowed to communicate through
b. SSID and MAC address
c. IP and MAC address
d. SSID and WEP key

Floods the Ethernet frame out all interfaces except the received interface
2.) When a switch receives an Ethernet frame to an unknown destination MAC address the switch applies the following logic:
a. IP and MAC address
b. SSID and WEP key
c. Floods the Ethernet frame out all interfaces except the received interface
d. SSID and MAC address

a PPP Multilink
45.) PPP protocol supporting binding many links into a single logical link in support of load balancing traffic across parallel links is referred to as
a. PPPoE
b. PPTP
c. a PPP Multilink
d. SLIP

Single collision domain requires all devices on a segment to share the available bandwidth
3.) Which of the following describes the collision domain design trade-offs?
a. Double frequency domain requires all devices on a segment to share the available bandwidth
b. Single collision domain requires all devices on a segment to share the available bandwidth
c. Single frequency domain requires all devices on a segment to share the available bandwidth
d. Double collision domain requires all devices on a segment to share the available bandwidth

Neighbor solicitation
5.) Which part of IPv6 neighbor discovery replaces the capabilities of ARP?
a. Neighbor solicitation
b. Switchport mapper
c. Network mapper
d. Packet sniffer

ANSI
11.) Which one of the following is an encapsulation type of Frame Relay LMI?
a. ATM
b. ANSI
c. E1/T1
d. SCP


Destination Unreachable-Code Network unreachable
17 Which type of ICMP message will be returned to host by a remote router if that router does not have a route to network?
a. Connect all the switches to a battery backup.
b. Connect all the switches to a generator.
c. Destination the data centers power to a generator.
d. Destination Unreachable-Code Network unreachable

False
9.) IPv6 broadcast addresses are used in similar manner to IPv4 broadcast addresses.
True or False

99.1.0.0/22
12.) Which one of the following summary routes correctly includes the subnets 99.1.1.0, 99.1.2.0, and 99.1.3.0, mask 255.255.255.0 but does not include more prefexes than nessessary?
a. 98.1.3.0/22
b. 99.1.2.0/32
c. 99.1.1.0/22
d. 99.1.0.0/22


Records the MAC address and incoming port to create the MAC address/interface table entry
14.) When a bridge/switch receives an Ethernet frame into a interface, what does it do with the source MAC address?
a. Records the MAC address and incoming port to create the MAC address/interface table entry
b. Enabling MAC address filtering on a switch
c. Add the MAC address to the host file.
d. Utilities shows the relationship between a MAC address and the corresponding IP address

Transparent
15.) Which VTP mode configures the switch to receive and forward VTP messages but does not use the VTP messages to update the local VLAN database?
a. Port authentication
b. Trunking
c. Snips
d. Transparent

Cross-over
6.) Which type of UTP cabling is required to connect to hosts back-to-back?
a. Cross-over
b. Roll-over
c. coaxial
d. fiber optic


False
18.) Configuring route summarization is the same configuration steps for all routing protocols.
True or False

Area border router (ABR)
19.) Which type of OSPF area router connects two areas?
a. NAT
b. DNS
c. Area border router (ABR)
d. SNMP

FFFF.FFFF.FFFF
20.) Which of the following is the MAC broadcast address for Ethernet?
a. FFFF.FFFF.FFFF.FFFF
b. FFFF.FFFF.FFFF
c. FFFF.FFFF.
d. FFF.FFF.FFF.FFF

Dynamic desirable
4.) When setting a local switchport to initiate the negotiation of a trunk link with the remote switch, the administrative mode is called ____.
a. Crossover