Facility Design Essay

Words: 1235
Pages: 5
Open Document
Rutgers University

Safety & Security Systems
Chapter 4

“We’re in Hot Water Now”
A Case Study Paper Submitted on
“What factors contributed to Solomon Alvi’s Injuries”

For the Partial Fulfillment of the Degree Requirements Of
Hospitality Management

By
Erin Adasczik

Erin Adasczik
Bill Coulter
Hospitality Facilities Management & Design
October 11, 2010
“We’re in Hot Water Now”
A Case Study Paper Submitted on
“What factors contributed to Solomon Alvi’s Injuries”

As president of the National Association of Safety Regulators, Solomon Alvi, had booked a hotel stay for his convention. This was the hotels first convention in 30 years. What seem to be a pleasurable stay ended up to be a catastrophe! The …show more content…
Then he took a break and wanted to take a relaxing hot shower before calling room service. He turned on the water and was surprised to feel the water warm, even though he over-heard the news at the front desk. He stepped into the tub and started washing himself. While in the shower, the water turned hot! Little did he know, down in the maintenance shop, the pipe work was completed between the hot water heaters. Joshua, the engineer, turned on the switch to start pushing the laundry’s hot water into the system. Back in room 933, Mr. Alvi was still in the shower when he got blasted with the scalding hot water. He screamed, took a step back, and slipped on the tub floor. He reached for the grab-bar as he began to fall, but ripped it out of the wall. He got smacked in the eye with the bar and got hit in the face with chunks of the tile and drywall as he fell and hit his head on the tub’s side while the scolding hot water continued to run down his body. Mr. Alvi managed to get out of the tub and poured the ice from the ice bucket over his red burnt body. He wrapped some ice in a washcloth and applied it to his eye. Knowing he knew he would have a shiner tomorrow addressing the members. He put his robe on and picked up the phone calling for emergency medical care. Mr. Solomon Alvi did not expect a incident like this would happen to him. There were a few factors
Show More

Related Documents: Facility Design Essay

1st Coursework For Facilities Management Essay

The Added Value of Facilities Management: Early Involvement of Facilities Management and Benchmarking Wang Hao ID: 40101577 Construction & Project Management School of Planning, Architecture and Civil Engineering Queen’s University Belfast Table of Contents 1. Introduction 2 2. Literature Review 3 2.1. Early FM Involvement 3 2.1.1. The benefits of the involvement of FM in the design process 3 2.1.2. The barriers of the involvement of FM in the design process 4 2.2. Benchmarking 4 2.2.1. The…

Words 2512 - Pages 11

Enbrel Manufacturing Case Study

Phase 2: Basic Design Process and instrumentation diagrams 3. Phase 3: Detailed Design Detailed Architectural Drawings Enbrel manufacturing facilities should be designed:  To provide simple material and personnel work flows to minimise possibility of contamination of/ by the product(s)  To fully contain and minimise areas where the product may be exposed  To provide manufacturing facilities which are easy to clean, and prove clean, and which facilitate…

Words 914 - Pages 4

Engineering Discipline

chemistry, physics, and engineering to design an operation of plants for the production of materials that undergo chemical changes during their processing • Responsible for new and improved products and processes: – New fuels for rockets, reactors, and booster propulsion – Medicines, vaccines, serum, and plasma – Plastics, synthetics and textiles Civil and Construction Engineering • Plan, design, and supervise the construction of facilities in both the public and private sectors…

Words 476 - Pages 2

Stress: Medicine and Clinic / Health Unit Space Essay

OVERVIEW The Clinic/Health Unit space types are facilities where outpatient ambulatory health services are provided. Sub-space types, such as office spaces, private toilets, and filing and storage areas are included. This space type does not include provisions for invasive surgery, in-patient services, medical diagnostic categories I, II, and III equipment (including exam lights and medical gas systems), radiological diagnostic services (including special structural elements and radiation shielding…

Words 904 - Pages 4

Mcclaren Wilson & Lawrie, Inc. Case Study

McClaren, Wilson & Lawrie, Inc. (MWL) was founded in 1995 with an exclusive commitment to the planning and design of public safety and civic facilities, forensic science laboratories and forensic pathology facilities. MWL has achieved international recognition with projects consisting of 275 public safety facilities and 130 forensic science laboratory and medical examiner facilities in 44 states and three Canadian provinces. MWL’s clients include a diverse range of government entities at municipal…

Words 212 - Pages 1

Essay on American Disabilities Act

American Disabilities Act Ashley’s Part What are issues to consider when meeting the International Building Code for a facility? There are many issues to consider when meeting The International Building Code for a facility in. One of the issues to think through is amendments to codes that are already set into place. Where there is a conflict between a general requirement and a specific requirement, the specific requirement shall be applicable. Where, in any specific case, different sections of this…

Words 398 - Pages 2

Module 2rrv 2part Essay

Chapter 2: Product, Process, & Schedule Design Dr. Rosario Rosas-Vega IE 4355 : Facilities Design Texas State University Schedule Design     Schedule design decisions provide answers to questions involving how much to produce and when to produce. Production quantity decisions are referred to as lot size decisions. Determining when to produce is referred to as production scheduling. How low production will continue? Impact of Schedule Design 1. Machine selection 2. Number of machines 3…

Words 907 - Pages 4

CHINESE AUTOMOTIVE INDUSTRY Essay

been proven to be very profitably but so far has not been recognized particularly for unique design practices.(1) Most Chinese domestic manufactures are known for knock-down kits that resemble import OEM products. However like the developing countries in Asia before it such as Korea and Chinas design language is beginning to evolve.(2) General motors GM EN-V concepts are one of the first designs the joining venture between GM and SAIC have produced specifically for the market. It is a personal…

Words 560 - Pages 3

Cash Flow and supply Chain Modeling Essay

Network Design in a Supply Chain Facility Location Models MGO 636 Supply Chain Modeling Design & Optimization 1 Outline • Background • Major Factors & Framework • Network Design Models – Plant Location Model – Demand Allocation Model – Plant Location Model with Multiple Sourcing – Plant Location Model with Single Sourcing MGO 636 Supply Chain Modeling Design & Optimization 2 Distribution Network: Plant, DC, Warehouse Customer DC MGO 636 Supply Chain Modeling Design & Optimization 3 Network…

Words 2664 - Pages 11

Facility Layouts of Mcdonalds- India, Pizza Hut-India & Dominos Pizza- India Essay

INTRODUCTION In order to maximizing the effectiveness of production processes and meeting employee needs & desires Facility layout and design plays a key role in business's overall operations. It entails in determining the placement off departments, work group within the departments, workstations, machines & stock holding points within a production facility. DEFINITION: “The physical arrangement of everything needed for the product or service, including machines, personnel, raw materials…

Words 2252 - Pages 10